Dodge Nitro: Garage door opener
HomeLink replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink unit operates off your vehicleвЂ™s battery. The HomeLink buttons that are located in the headliner or sun visor designate the three different HomeLink channels.
NOTE: HomeLink is disabled when the Vehicle Security Alarm is active.
вЂў Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a вЂњstop and reverseвЂќ feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1вЂ“800вЂ“355вЂ“3515 or, on the Internet at www.HomeLink.com for safety information or assistance.
вЂў Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death.
Before You Begin
If you have not trained any of the HomeLink buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. It is recommended that a new battery be placed in the handheld transmitter of the device that is being copied to HomeLink for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage when programming. 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the handheld transmitter away from the HomeLink button you wish to program.
Place the handheld transmitter 1вЂ“3 in (3-8 cm) away from the HomeLink button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLink button and the handheld transmitter button until the HomeLink indicator changes from a slow to a rapidly blinking light, then release both the HomeLink and handheld transmitter buttons. Watch for the HomeLink indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you train.
вЂў Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the вЂњGate Operator/Canadian ProgrammingвЂќ section.
вЂў After training a HomeLink channel, if the garage door does not operate with HomeLink and the garage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to the heading вЂњProgramming A Rolling Code System.вЂќ 4. Press and hold the just-trained HomeLink button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink button is pressed. If the indicator light blinks rapidly for two seconds, and then turns to a constant light, continue with programming for a Rolling Code. 5. PROGRAMMING A ROLLING CODE SYSTEM. At the garage door opener motor (in the garage), locate the вЂњLearnвЂќ or вЂњTrainingвЂќ button.
This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door).
1 вЂ” Garage Door Opener 2 вЂ” Training Button
6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer.
NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7. Return to the vehicle and press the programmed HomeLink button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1вЂ“800вЂ“355вЂ“3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink buttons, repeat each step for each remaining button. DO NOT erase the channels.
Gate Operator/Canadian Programming
Canadian radio-frequency laws require transmitter signals to вЂњtime-outвЂќ (or quit) after several seconds of transmission вЂ“ which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to вЂњtime-outвЂќ in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace вЂњProgramming HomeLink вЂќ Step 3 with the following: 3. Continue to press and hold the HomeLink button, while you press and release (вЂњcycleвЂќ), your handheld transmitter every two seconds until HomeLink has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under вЂњProgramming HomeLink вЂќ earlier in this section.
To operate, press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, Security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time.
Reprogramming A Single HomeLink Button
To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Programming HomeLink Step 2 and follow all remaining steps.
It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink Universal Transceiver is disabled when the Vehicle Security Alarm is active.
If you are having trouble programming HomeLink , here
are some of the most common solutions:
вЂў Replace the battery in the original transmitter.
вЂў Press the LEARN button on the Garage Door Opener to complete the training for a Rolling Code.
вЂў Did you unplug the device for training, and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1вЂ“800вЂ“355вЂ“3515 or, on the Internet at www.HomeLink.com for information or assistance.
This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the userвЂ™s authority to operate the device. The term IC before the certification/registration number only signifies that Industry Canada technical specifications were met.
Opening and closing the side outlets
1 Open the vent. 2 Close the vent. ■Using the automatic mode Fan speed is adjusted automatically in accordance with the temperature setting and ambient conditions. In addition, the follo ...
Your authorized dealer has touch-up paint to match your vehicleвЂ™s color. Take your color code (printed on a sticker in the driverвЂ™s door jamb) to your authorized dealer to ensure you get the c ...
Luggage Restraint Loops (if equipped)
Luggage Restraint Loops (if equipped) Four luggage restraint loops are provided on the luggage compartment floor. An optional rubber net can be hooked to these loops to help keep cargo from movi ...