Jeep Liberty: Manual Operation
This system offers a full complement of manual override features, which consist of Blower Preferred Automatic, Mode Preferred Automatic, or Blower and Mode Preferred Automatic. This means the operator can override the blower, the mode, or both. There is a manual blower range for times when the AUTO setting is not desired.
The blower can be set to any fixed blower speed by rotating the Blower Control knob (on the left).
NOTE: Please read the Automatic Temperature Control Operation Chart that follows for details.
The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions.
Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow.
NOTE: The center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear.
Air is directed through the panel and floor outlets.
NOTE: For all settings, except full cold or full hot, there is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets.
This feature gives improved comfort during sunny but cool conditions.
Air is directed through the floor outlets with a small amount flowing through the defrost and side window demist outlets.
Air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.
Air is directed through the windshield and side window demist outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting.
вЂў Air Conditioner Control
Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn OFF the air conditioning. An LED in the button illuminates when manual compressor operation is selected.
вЂў Recirculation Control
The system will automatically control recirculation.
However, pressing the Recirculation Control button will temporarily put the system in recirculation mode (ten minutes). This can be used when outside conditions such as smoke, odors, dust, or high humidity are present. Activating recirculation will cause the LED in the control button to illuminate.
After ten minutes, the system will return to normal AUTO mode function and the LED will turn off.
вЂў When the ignition switch is turned to the LOCK position, the recirculation feature will be cancelled.
вЂў In cold weather, use of the Recirculation mode may lead to excessive window fogging. The Recirculation mode is not allowed in the floor, defrost, or defrost/ floor mode in order to improve window clearing.
Recirculation will be disabled automatically if these modes are selected.
вЂў Extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, press the Recirculation button to return to outside air.
Some temp/humidity conditions will cause captured interior air to condense on windows and hamper visibility. For this reason, the system will not allow Recirculation to be selected while in floor, defrost, or defrost/floor mode. Attempting to use the recirculation while in these modes will cause the LED in the control button to blink and then turn off.
вЂў Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into Recirculation Mode at this time. If you would like the system to go into Recirculation Mode, you must first move the Mode knob to Panel, Panel/Floor and then press the Recirculation button. This feature reduces the possibility of window fogging.
(If installed) This system is designed to provide protection from unauthorized entry into the car. This system is operated in three stages : the first is the "Armed" stage, the second ...
List of storage features
1 Cup holders 2 Bottle holders 3 Auxiliary box 4 Glove box 5 Overhead console 6 Console box CAUTION ■Items that should not be left in the storage spaces Do not leave glasses, lighters ...
Tow ball options
Tow ball options 1. Bolt on tow ball onto flange. 2. Fixed swan neck tow ball. 3. Detachable tow ball. 4. Receiver for hitch (drawbar). Australia only. ...